If you are experiencing the problem of the Maytag dishwasher leaking, then we have the troubleshooting guide for you. Maytag dishwashers are one of the most popular brands on the market, and customers often trust their Maytag brand product to be high quality.
Maytag dishwashers can experience many different types of problems that will require a professional to fix them, but this article will help diagnose and troubleshoot your Maytag dishwasher so that it is running like new again in no time!
What Causes Maytag Dishwasher Leaking? Troubleshooting and Diagnosis
Maytag dishwasher leaks can be frustrating, but they are usually not difficult to fix. Let’s look at the possible causes and solutions for it.
Using the Wrong Detergent
When your dishwasher leaks soap bubbles or leaks from the door, it’s probably because you are using the wrong kind of detergent. Dish detergent needs to make suds when it cleans the dishes. If the soap/detergent is not designed for use in a dishwasher or if you are using hand-washing dish soap, there will be too much suds around the door and they will leak out of the opening around the door. To fix this problem, change your type of detergent and see if it happens again.
Tip: When switching to new detergents for the first time, run an empty cycle before filling up with dishes so that all traces can get cleaned out properly.
Maytag Dishwasher is Overloaded
To make sure the dishwasher can clean everything, don’t overfill it. Run it when it is full, but not more than that. This way, you will save time and resources. When the dishwasher is running, if there are dishes in there for too long, they won’t get fully cleaned and may cause the dishwasher to leak, and also you have to rinse the dishes again (causing wear on your machine).
If you put too many dishes in your dishwasher, the water cannot make its way to the bottom of the dishwasher to get them clean. This is because it is blocked by all of the dishes that are in front of it. The water will splash out from under the door because it can’t go anywhere else. But if you take out some of your dishes, there will be less in front, and no more water will spill out.
Dishwasher is Unlevel
When the dishwasher is not level, it will cause water to spill out before and during your wash cycle. Maytag recommends adding a couple of inches for height, so there are no leaks on one side or another. You can do this by placing bricks underneath the legs that are too short for your machine (if any).
To make sure your dishwasher is sitting flat on the floor, you can use a level to check if the top of it is level. If it’s not, adjust or replace the legs until it is. Make sure that you put the anti-tip brackets back on after adjusting them or installing them.
Faulty Water Inlet Valve
The bottom of the Maytag dishwasher has a water inlet valve which allows water to flow into the dishwasher at cycle times. If this valve doesn’t open and closes properly, your appliance may overflow, leaking excess water out onto your floor.
Run your dishwasher and open the door halfway through for a mid-cycle check. If water continues to fill, you might have an inlet valve defect that will need service soon. This part can’t be repaired, so you’ll need to buy a new one and follow the manufacturer’s instructions for installation.
Loose Pump Seal
A Maytag dishwasher pump is the main part that circulates water in your appliance. It’s possible for the pump seal to become loose and start the issue of the Maytag dishwasher leaking, so it should be inspected when you run a full cycle (without dishes) with just water in there. If water is leaking from the drain pump, it’s likely that the impeller and seal are causing the problem.
Run a second cycle without any soil or food particles to check if the leak has stopped completely. If not, then tighten up those screws! Be careful not to over-tighten them, though – they may strip out of place and require replacement instead of repair. The Maytag dishwasher’s pump also might need cleaning periodically.
Damaged Latch or Gasket
The Maytag dishwasher’s latch may be damaged, or its rubber gasket might need to be replaced. If the door won’t close properly when you try to shut it, then there is a chance that this could be your issue. Make sure all of the screws are tightened securely before proceeding with further troubleshooting steps.”
Loose, cracked, or damaged door gaskets can cause water to escape from a dishwasher’s doors. If they are loose, you can secure them back in place, but if they were damaged, then you must replace them.
Check behind the dishwasher if there are any items such as silverware or other large food particles lodged between the door seal and tub. These can prevent water from being properly sealed inside and stop it from draining fully.
Faulty Float Switch
A float is located at the bottom of the dishwasher tub. It is a safety device to prevent water from overflowing and flooding the kitchen if something goes wrong. The float moves up and down in relation to the water level.
When the dishwasher is full, a sensor activates to turn off the water inlet valve. If the dishwasher is filling with far too much water and leaking, the float or the float switch may be broken. Remove the float and test it with a multimeter to determine if it is faulty or not. If defective, replace it.
Stuck or Clogged Spray Arm
If water is unable to spray from the dishwasher arm, there may be a clog or something stuck in it. The best way to troubleshoot this issue is by opening the door and observing if any food particles have collected around the discharge outlet of the spray arm. If they are present, remove them with tweezers before running another load. But if no debris can be found close to where the water exits out of the dishwasher, you will need to replace it as soon as possible due to a faulty mechanism that caused the blockage.
You can remove the spray arm by turning it counter-clockwise. Inspect for signs of damage or obstruction and order replacement parts as necessary from the manufacturer or dealer.
Check Dishwasher Pump and Hose
If water is leaking into the dishwasher from inside or from the pump area, it may be coming from a leaky pump or hose. Maytag dishwashers have six-foot hoses which should not kink when in use.
Check to make sure there are no bends and that they are fully extended with no twists or folds.
A Maytag dishwasher typically has two pumps: one for the upper rack and one for the bottom rack (if applicable). If either of these parts is leaking, you will need to replace it right away, as this can cause serious damage to your kitchen flooring if left unchecked.
We hope that now you are not facing the Maytag Dishwasher leaking problem. Please do comment with your questions, and we will be happy to answer them.
Hi there! I’m Sam Hendricks, and I’m a repair technician and expert. I created this website to help people like you save money and time by fixing your own appliances.
Over the years, I’ve seen people spend a lot of money on unnecessary repairs or replacements. That’s why I decided to share my expertise and create easy-to-follow guides for fixing appliances on your own.