Maytag Washer Stopped Working Full Of Water (How To Fix)

If your Maytag washer has stopped working in the middle of a cycle and is full of water, it can be frustrating and concerning. There can be several causes for this issue, but the good news is that most of them can be fixed without the help of a professional. Before calling a technician, it is worth checking some common causes of this problem and trying some simple fixes.

One possible cause for a Maytag washer stopping mid-cycle is a faulty lid switch. This switch ensures that the washer does not run with the lid open and can sometimes malfunction, causing the washer to stop running altogether. Another possible culprit could be a clogged drain hose or filter, preventing the water from draining properly. Check for any blockages and debris and clear them out if necessary.

In some cases, the issue lies with the control board or motor of the washer. These parts can become worn out or damaged over time and may need to be replaced. However, it is important to troubleshoot other possible causes before jumping to this conclusion.

Causes of Maytag Washer Stopped Working Full Of Water

A Maytag washer not completing its cycle and stopping full of water can be frustrating for any homeowner. There can be several causes for this issue, including power supply and drainage system issues, as well as lid switch malfunctioning.

Power Supply Issues:
One of the most common causes of a Maytag washer stopping full of water is power supply issues. If the power supply to the washer is interrupted or unstable, it can cause the machine to stop working mid-cycle. Power surges, tripped circuit breakers, and faulty wall sockets can all interrupt the power supply to the washer. In such cases, homeowners should check the power cable and wall socket, or contact a professional electrician for assistance.

Drainage System Issues:
Another common cause of a Maytag washer stopping full of water is drainage system issues. If the drainage system is clogged or blocked, it can prevent the washer from draining the water properly, causing it to stop working mid-cycle. Over time, dust, lint, and debris can build up in the drainage system and clog it. To fix this issue, homeowners should clean the drainage system regularly and remove any obstruction that may be causing the blockage.

Lid Switch Malfunctioning:
The lid switch is an essential component of the Maytag washer, as it senses when the lid is closed and locks it to prevent accidents. If the lid switch is malfunctioning, it can cause the washer to stop mid-cycle, even if the lid is closed. To fix this issue, homeowners should check the lid switch and make sure it is functioning properly. If it is damaged or broken, it may need to be replaced.

Fixes for Maytag Washer Stopping Full of Water

A malfunctioning washing machine can be frustrating and inconvenient, especially one that stops working in the middle of a cycle while full of water. Fortunately, there are several fixes that can rectify this problem without calling for professional help. Here are some of the primary causes of the issue and the solutions that one can attempt.

Power Supply Related Fixes:

One reason for a Maytag washer to stop working full of water is a power supply issue. First, check the electrical outlet to ensure it is functional. If it is, unplug the washer and let it sit for 30 minutes before plugging it back in; this will reset the washer’s control board. Another issue could be a faulty circuit breaker; reset it if it is tripped. Lastly, if there is no power supply issue, one can check if there is a blown fuse inside the washer’s control panel.

Drainage System Related Fixes:

A clogged or faulty drainage system could be the cause of the problem. First, ensure that no foreign objects are blocking the drain hose. If that does not work, locate the washer’s drainage pump and clean it out. Another possibility is that the washer’s pressure switch is stuck in the full position, causing the washer to believe it is still full of water. Check the switch’s wiring for any malfunction; if it is fine, replace the entire switch.

Lid Switch Fixes:

If the washer begins its cycle as normal but then stops unexpectedly, it could be due to a malfunctioning lid switch. The switch’s role is to detect if the lid is closed, and if not, it prevents the washing machine from filling with water. Test the switch by manually depressing it; if the washer begins to work normally, then the switch was the culprit. Replace the lid switch if it is faulty.

In conclusion, a Maytag washer stopping full of water can be a headache, but there are several solutions that one can attempt before calling for professional help. If none of the above fixes work, it might be time to contact a professional. However, most of the time, one can solve the issue by checking the power supply, drainage system, and lid switch. By following the above tips, one can prevent this frustrating problem from occurring in the future.

Easy DIY Fixes

If your Maytag washer has stopped working and is full of water, here are some easy DIY fixes you can try before calling a technician.

Drain and Siphon Water Out

The first and most common cause of a Maytag washer stopping mid-cycle is the drain and siphon being clogged or blocked. To fix this, manually drain the water from the machine using a hose or bucket. Once the water is drained, locate the drain hose and detach it carefully. Clean out any debris or blockages in the hose, and reconnect it securely.

If the drain hose itself is not blocked, try siphoning the water out of the machine using a flexible hose. Insert one end of the hose into the washing machine’s water outlet and the other end into a bucket. Once the water starts to flow out of the machine and into the bucket, the siphoning process will continue automatically.

Check the Drainage Hose

Another possible reason for the Maytag washer stopping mid-cycle is a damaged drainage hose. If you notice any visible cracks or holes in the hose, it may need to be replaced. However, if the hose appears to be intact, make sure it is still firmly connected to the washing machine and the water outlet.

Test the Drain Pump

If the first two solutions do not fix the problem, you may need to test the drain pump. Start by unplugging the machine and removing the access panel at the back. Locate the drain pump and check for any blockages or obstructions. If everything appears to be in order, use a multimeter to verify that the pump is receiving power and functioning properly.

In conclusion, there are several potential causes of a Maytag washer stopping mid-cycle. While some issues may require professional repair, many can be fixed easily with a little DIY knowledge and effort. By following the steps outlined above, you can save time and money while restoring your Maytag washer to full working order.

When To Call a Professional

If your Maytag washer stopped working full of water, and you’re not sure what the problem is, you may be tempted to try and fix it yourself. However, there are some situations where it’s best to call in a professional. Here are a few points to consider:

Dangerous Fixes

Some of the issues that can cause your Maytag washer to stop working full of water can be dangerous to attempt to fix on your own. For example, if the motor or wiring is damaged, you could risk electrical shock or fire if you don’t know what you’re doing. Similarly, if the water valve is broken, water could leak out and cause damage to the area around the washer. If you’re not confident in your ability to safely make these types of repairs, it’s best to call a professional.

Complex Repairs

Even if the problem with your Maytag washer doesn’t seem particularly dangerous, there are some repairs that can be quite complex. For example, if the drum inside the washer is damaged, it may require special tools and expertise to replace it. Similarly, if the control panel isn’t functioning properly, you may need professional help to diagnose and fix the problem. Complex repairs like these are often best left to the experts.

Unfamiliar with Washing Machine Mechanics

If you’re not familiar with washing machine mechanics, it can be difficult to diagnose what’s causing your Maytag washer to stop working full of water. There are many different components that can contribute to a malfunction, from the motor to the water pump to the electronic controls. If you don’t have experience working with these types of systems, it can be tough to figure out what’s going on. In these cases, it’s often best to call in a professional who has the expertise and training to diagnose the problem correctly.

Ultimately, deciding whether or not to call in a professional to fix your Maytag washer is a personal choice. If you feel comfortable making the necessary repairs on your own, and you have the tools and knowledge to do so safely, it may be worth giving it a try.

However, if you’re unsure about any aspect of the repair process, or you don’t have the time or resources to take on the task yourself, it’s a good idea to seek professional help. By doing so, you’ll ensure that your washer is repaired correctly and safely.

Conclusion

In conclusion, a Maytag washer stopping working full of water can be quite frustrating, but it does not necessarily mean the end of its lifespan. The most probable cause of this issue is a faulty lid switch or a malfunctioning drainage system. Checking and fixing these components can solve the problem and ensure the washer works efficiently again.

However, it is essential to note that regular maintenance can prevent such issues from occurring in the first place. Always ensure that you clean your washer regularly, check its components, and avoid overloading it.

Investing in a Maytag washer is a long-term commitment and requires proper care and maintenance. By following these guidelines, you can enjoy years of reliable service from your Maytag washer.

FAQs

What are the common causes of a Maytag washer stopping mid-cycle?

The common causes of a Maytag washer stopping mid-cycle are power outage, clogged drain hose or pump, faulty lid switch, overheated motor or a malfunctioning computer board.

What should I do if my Maytag washer is still full of water?

If your Maytag washer is still full of water, turn off the power and try to drain the water manually by using a hose or bucket. If the issue still persists, check the drain hose and pump for clogs or damage.

Why is my Maytag washer not draining water?

Your Maytag washer might not be draining water due to a clogged drain hose, faulty pump, or a malfunctioning computer board. Make sure to check the drain hose and pump for obstruction and damage and replace them if necessary.

How can I fix a Maytag washer with a faulty lid switch?

If your Maytag washer has a faulty lid switch, you can fix it by replacing the switch with a new one. Make sure to unplug the washer from the power source and refer to the user manual for instructions on how to replace the lid switch.

What should I do if my Maytag washer has an overheated motor?

If your Maytag washer has an overheated motor, turn it off and unplug it from the power source. Wait for it to cool down and check for any obstructions that might have caused the motor to overheat. You might need to replace the motor if it has sustained damage.