Running Dryer Without Thermal Fuse [How To Bypass and Is It Good?]

Having a dryer that won‘t turn on can be a frustrating experience. If you‘ve determined that the issue is due to a faulty thermal fuse, you may be wondering if it‘s possible to bypass it and get your dryer working again. In this article, we‘ll discuss the risks and benefits of bypassing a thermal fuse and provide instructions on how to do it safely.

Are you uncertain as to how you can go about bypassing the thermal fuse on your dryer? If so, then you are in the right spot! We are here to assist you with this task. To pass a thermal fuse, you will need to begin by turning the dryer on, then detaching the two wires from the thermal fuse and attaching them to a power source.

Ignoring a thermal fuse is definitely risky. While it’s tempting to run the dryer off the fuse or to neglect to replace the fuse after you’ve cut it, don’t do it! This can lead to more costly repairs down the road.

Running Dryer Without Thermal Fuse – Step By Step Instruction

Bypassing the fuse is never a longterm solution. You need to fix the problem that caused the thermal fuse to blow in the first place.

Bypassing a thermal fuse on your dryer may seem like an easy fix, but it may cause your dryer to malfunction and burst into flames in no time at all. Let’s get more details about how can you bypass a thermal fuse from here!

You can bypass the thermal fuse on a dryer when troubleshooting or diagnosing it, but using a multimeter is more reliable. The thermal fuse in a dryer is one component you should check for problems with your dryer (aside from the obvious ones like broken wires, blown fuses and tripped breakers).

A Thermal fuse is a safety measure in your dryer that prevents overheating and fire hazard. In order to begin troubleshooting, it’s best to bypass the thermal fuse without removing it by using an inline jumper wire.

Here are step by Step instruction:

A thermal fuse on a dryer is a small device that is designed to help prevent fires by cutting off power to the dryer if it begins to overheat. The thermal fuse is usually located on the back panel of the dryer, near the blower wheel or motor. It typically looks like a small cylindrical device with two wires connected to it.

It is important to know how to bypass a thermal fuse on a dryer, as it can save you time and money if the device needs to be replaced.

The first step in bypassing a thermal fuse on a dryer is to unplug the dryer from the wall outlet. Once the plug has been removed, you will need to access the thermal fuse from the back of the dryer. It is typically held in place with two screws, so you will need to remove the screws and then carefully pull the thermal fuse away from the back of the dryer.

Once you have removed the thermal fuse, you will need to locate the two wires connected to it. These two wires are usually connected to two small terminals on the thermal fuse. You will need to use a pair of pliers to remove the wires from the terminals. Once the wires have been removed, you can then connect them directly to each other using a small piece of electrical tape. This will effectively bypass the thermal fuse and allow the dryer to operate normally.

It is important to remember that bypassing the thermal fuse on a dryer is only a temporary solution, and it should not be done as a long-term fix. The thermal fuse is designed to prevent fires and other serious problems, so it is important to replace the thermal fuse as soon as possible.

Additionally, you should never attempt to bypass any other safety devices, such as a thermal cut-off switch or a high-limit thermostat, as these devices can also help to prevent fires.

What Happens If You Bypass A Thermal Fuse?

When a thermal fuse is correctly installed, it will safely shut off the power to the circuit if the temperature gets too high. This prevents the circuit from being damaged by heat or over-current, which can be a potential fire hazard.

However, if a thermal fuse is bypassed, the circuit will remain powered without any protection from overheating. This can cause the circuit to overheat, leading to damage or even a fire. It is important to note that bypassing a thermal fuse is never recommended and should be avoided at all costs.

When a thermal fuse trips, it is an indication that something is wrong with the circuit and needs to be fixed. It could be a loose connection, a short circuit, or an overloaded circuit. Once the cause of the problem has been identified, the thermal fuse can be replaced and the circuit will be protected once again.

In summary, bypassing a thermal fuse is a dangerous practice that can lead to damage, fires, and other serious consequences. It is important to always replace a thermal fuse when it trips, and to identify and address any underlying issues that may be causing the fuse to trip in the first place.