Why Is My Drain And Spin Cycle Adding Water [SOLVED]

Put simply, the drain and spin cycle is a method by which clothes are washed in a washing machine. The machine spins the clothes at a very high speed and then drains out the excess water. This process thoroughly washes your clothes and makes them look clean.

But have you ever wondered why does this cycle add water in spite of draining the excess water? Or maybe you have never used the drain and spin cycle yourself. This article will explain all of it to you.

When your washing machine fills with water during drain and spin, it’s a problem related to the water valve or drain. You can troubleshoot the problem yourself, but take precautions to protect yourself from the water.

Why Is My Drain And Spin Cycle Adding Water – Troubleshoot And Diagnosis

Let’s see some of the possible causes and solutions.

1. Faulty Water Valve

The water inlet valve in a washing machine is responsible for controlling the flow of water into the washer. The valve is located at the point where the water supply hose attaches to the back of the washer.

The valve opens and closes to allow water to enter the washer when it is turned on, and then shuts off the water flow when the washer is turned off.

the problem can be likely due to a defective water inlet valve. This can be a serious problem, as it can cause your washer to overflow. If you think your washer’s water inlet valve is defective, check for these signs:

• Water leaking from the valve
• Water not flowing into the washer
• Washer not draining properly

If you notice any of these signs, it’s best to call a professional for help. Trying to repair a defective water inlet valve on your own can be dangerous, so it’s best to leave it to the experts.

Over time, sediment can build up in the valve and cause it to fail. Testing and replacing the water inlet valve is a relatively simple process that can be done in a few minutes.

To test the water inlet valve, first disconnect power to the washing machine. Next, remove the hose from the back of the machine. Place a bucket under the hose to catch any water that may come out when you remove it. Once the hose is removed, use a multimeter to test for continuity through the two wires attached to the valve.

If there is no continuity, then the valve will need to be replaced.

2. Clogged Or Kinked Drain Hose

If your washing machine is adding water during the drain and spin cycle, it is most likely due to a clogged or kinked drain hose. This is a relatively easy problem to fix and only requires a few minutes of your time.

First, locate the drain hose on your washing machine. If it is clogged, you will see water standing in the hose or coming out of it slowly. If it is kinked, you will see a bend or kink in the hose.

To fix a clogged drain hose, simply remove the hose from the washing machine and clear out any obstruction that you see. To fix a kinked drain hose, simply straighten out the hose so that there are no more bends or kinks in it.

3. Siphoning Issue

If the drain hose on your washer is siphoning water back into the tub during the spin cycle, it could be because the drain house is pushed too far down the standpipe.

If the drain house is pushed too far down the standpipe, it will create a vacuum that can siphon water back into the washer. There needs to be an airgap between the end of the drain hose and the standpipe in order to prevent this from happening.

The drain hose needs to be at least 30″ high to allow for proper drainage, which will allow the airgap to break the siphoning effect. If the drain hose is lower than that, it will need to be raised up.

You can do this by removing the hose from the standpipe and reattaching it at a higher point.

4. Loose Door Latch

This can be caused by a loose door latch. To fix this, first check that the latch is tightened correctly.

If it is, then you may need to adjust the strike plate so that it lines up with the latch correctly.

This can be a very easy problem to fix. Simply tighten the screws on the door latch. If this does not solve the problem, you may need to replace the door latch.

5. Control Panel Malfunction

If your washing machine is adding water during the drain and spin cycle, it may be due to a control panel malfunction. This can be a serious problem, as it can cause your clothes to become soaked and damaged.

If you notice this problem, you should unplug your washing machine and call a repair technician as soon as possible.

In the meantime, you can try to troubleshoot the problem by checking the control panel for any loose wires or connections.

Final Thoughts

In conclusion, it is important to ensure that your washer is draining and spinning properly to avoid any issues with adding water. If you notice that your washer is not draining and spinning correctly, then you should contact a professional for help.