Maytag Dryer Code F01 [Quick Solution] – Let’s Fix It

If you have a Maytag dryer that has stopped working and the F01 code is displayed, this post can help you. If you’re ready to troubleshoot the problem and need advice on how to fix it, keep reading. Or, if this is a Do It Yourself project, you’re in the right place.

Maytag dryers are among the most popular in the United States and for good reason. They last a long time, they’re highly effective, and they’re relatively inexpensive. However, even the best machines can break down, and this Maytag dryer code F01 troubleshooting guide is going to help you figure out how to repair your machine so you can get it back up and running ASAP.

All Whirlpool dryers are fitted with a control board that regulates the machine operation. If this board malfunctions, it will display an error code – in your case, F01.

This can usually be traced back to a power outage or power surge, but there are a few other possible causes. To troubleshoot and repair your machine without wasting time or money, follow our step-by-step instructions below.

Maytag Dryer Code F01 – Troubleshoot And Diagnosis

When you start your Whirlpool dryer and it displays the F01 error code, you may wonder if it’s time to get a new appliance. This error code can be caused by any number of things, from the power button being broken or damaged to electrical problems with the control board.

1. Do A Reset

In some cases, the dryer simply needs to be reset.

The first thing to do is to try resetting your dryer. To do that, simply disconnect your dryer from its power source and leave it turned off for a few minutes. After a few minutes, turn your dryer back on and see if the error code has gone.

Most of the time, this fixes the problem.

2. Inspect The Thermal Switch

A thermal switch is a device that is designed to protect an appliance or electrical circuit from excessive heat. The switch is typically located near the heating element of the appliance and is connected to a thermal sensor that monitors the temperature of the element.

If the temperature of the element exceeds a certain threshold, the switch will open and break the circuit, preventing the appliance from overheating.

There is no need to replace the whole part when the thermal switch may be defective. The part is responsible for protecting your dryer from overheating, and while it’s not common that the switch would be at fault, when it does happen, you have to install a new one rather than buying an entire piece of appliance. It could be located on any part of the machine — usually near the blower body, heating element, or gas burner — and that differs between models.

First, unplug the dryer from the power outlet. Then, remove the back panel of the dryer to access the thermal switch. Locate the thermal switch and disconnect the wires. Next, remove the mounting screws and remove the thermal switch.

Use a multimeter to test the thermal switch for continuity. If the switch is faulty, replace it with a new one. Install the new thermal switch by reversing the above steps.

Reattach the back panel and plug the dryer back in.

3. Faulty Thermistor

A thermistor is a precision resistor with a resistance that varies with temperature. In a clothes dryer, the thermistor monitors air temperature and sends a signal to the control board to adjust heating elements as needed.

If the thermistor is not working, the Maytag dryer will not start. To test the thermistor, use a multimeter to test for resistance. The thermistor should have a resistance of about 10,000 ohms at room temperature. If the resistance is not within this range, the thermistor should be replaced.

4. Door Switch Problem

The door switch is used to detect whether the dryer door is open or closed. When the door is open, the switch will open and the dryer will not start. When the door is closed, the switch will close and the dryer will start.

If the door is opened while the dryer is running, the switch will shut off the dryer.

The door switch is usually located near the top of the door opening.

When the dryer door is not locking properly it may cause an F01 error to be displayed.

Here are the steps to test the door switch:

1. 1. Unplug the dryer.
2. Remove the door panel to access the door switch.
3. Use a multimeter to test the door switch for continuity.
4. If the switch is defective, replace it with a new one.
5. Reassemble the door panel and plug in the dryer.

5. Control Panel Issue

The control panel is the interface between the user and the dryer. It is used to set the drying time, temperature, and other settings. The control panel may also include a display that shows the status of the dryer, such as the drying time remaining, the temperature, and the like.

If the laundry appliance suddenly displays a F01 error code, wiping down the top of the washer and surrounding areas may fix the issue. For more serious malfunctions, your best bet is to replace the control panel. Oftentimes, even when these crucial parts need to be replaced, it’s still less expensive than buying a new appliance.

When trouble comes along, you must have someone on hand who can tackle it for you.

Unplug the dryer power cord and remove the rear panel to access the dryer control panel. Visually inspect the control panel wiring for any loose, damaged, or burnt wires. Use a multimeter to check for continuity between the control panel terminals and the dryer motor. Replace the control panel if there is no continuity or the wiring is damaged.