Why Washer Adding Water During Spin Cycle [SOLVED]

The washing machine is a sophisticated piece of equipment that has been designed to take the hard work out of washing your clothes. However, even the most expensive brands will sometimes have faults and this can be frustrating to say the least.

We’re here to tell you all you need to know about why washing machine is adding water during spin cycle.

Chances are, as soon as you see water spraying out of your washer during the spin cycle, your immediate reaction is to panic. It may seem like a scary situation, but there’s really no need to worry — it’s probably not as bad as you think. That being said, it’s definitely something you should pay some attention to, especially since it can eventually lead to bigger problems.

Washer Adding Water During Spin Cycle – Troubleshoot And Diagnosis

Washer Adding Water During Spin Cycle

Let’s see some of the solutions.

1. Unbalanced Load

This can happen if there are too many items in the washer, or if the items are not evenly distributed. If this happens, your washer will not be able to spin properly and will end up adding water to the load.

To fix this problem, you will need to redistribute the items in the washer so that they are evenly balanced. You may also need to remove some items from the washer if there are too many.

There are a few easy ways to redistribute your clothes in the washer so that you avoid an unbalanced load.

First, you’ll want to make sure that you evenly distribute your clothes around the drum of the washer. You can do this by folding them in half or quarters and then placing them into the washer.

Next, you’ll want to add water to the washer so that it covers the clothes. The amount of water you add will depend on the size of your washer and the amount of laundry you’re doing.

Finally, you’ll need to redistribute the weight of the laundry by moving it around in the washer.

2. Shift Actuator

A shift actuator is a device in a washing machine that helps to move the inner tub and drive the agitator. The shift actuator is located near the bottom of the washer and is connected to the transmission. The actuator helps to engage and disengage the transmission, which allows the washer to operate in different modes.

See also  How To Reset Whirlpool Washing Machine 6th Sense - Step By Step Guide

For example, when the washer is in the spin cycle, the shift actuator will engage the transmission and spin the inner tub.

The shift actuator is located on the back of the washer and controls the position of the transmission. If the actuator is not working properly, it will cause the transmission to stay in one position and not move correctly.

This will cause the washer to add water during the spin cycle. To fix this problem, you will need to replace the shift actuator.

3. Reset The Washer

If your washing machine isn’t working properly, you may need to reset it. Follow these steps to reset your washer:

  1. Unplug the washing machine from the power outlet.
  2. Wait 30 seconds and then plug the washer back in.
  3. Press and hold the “Start/Pause” button for 5 seconds. This will reset the washer’s control panel.
  4. If your washer has a knob, turn it to the “Off” position and then back to the “On” position.
  5. Open and close the door of the washing machine several times within 30 seconds to complete the reset process.

4. Over Sudsing Problem

This can happen if you use too much detergent, or if the detergent you’re using isn’t compatible with your washer. Over sudsing can cause your washer to become unbalanced, and can damage clothing. To fix the problem, simply use less detergent, or switch to a different type of detergent.

You can solve this problem by using HE detergent. HE detergent is designed to produce fewer suds than regular detergent, so it’s less likely to cause an over sudsing issue.

5. Defective Water Level Sensor

The water level sensor is responsible for telling the washer how much water to add during each cycle. If the sensor is not working properly, it may cause the washer to add too much water. This can be a major problem because it can lead to overloading and damage to your washer.

If your washing machine isn’t draining properly, the water level sensor may be damaged and need to be replaced. Here’s how to test and replace the water level sensor in your washer:

  1. Unplug the washing machine from the power outlet.
  2. Remove the washing machine’s cabinet panel to access the water level sensor.
  3. Use a multimeter to test for continuity between the two terminals on the water level sensor. If there is no continuity, then the sensor needs to be replaced.
  4. To replace the water level sensor, disconnect the wires from the old sensor and attach them to the new sensor. Then, reattach the cabinet panel and plug in your washing machine.
See also  Samsung Washer FL Error Code [FIXED] - KCSCFM Repair

6. Faulty Water Inlet Valve

The function of the water inlet valve in a washing machine is to regulate the amount of water that enters the tub during each cycle. The valve is located at the back of the washer and is connected to the water supply line. The valve opens when the washer is turned on and allows water to flow into the tub.

The amount of water that enters the tub is controlled by a knob or dial on the control panel. The knob or dial is turned to the desired setting and the valve opens or closes accordingly.

To test the water inlet valve, disconnect the power and water supply to the washing machine. Then remove the hose from the back of the machine. Place a multimeter on the two terminals where the hose was attached. If you don’t get a reading of continuity, then it’s time to replace the water inlet valve.

To install a new water inlet valve, simply reverse the process you used to remove the old one.

7. Siphoning Issue

If your washer is adding water during the spin cycle, it may be due to a siphoning issue. There are two potential causes of this problem: the air gap is not installed correctly, or the drain hose is not up at least 42 inches from the finished floor.

If the air gap is not installed correctly, water can siphon back into the washer through the drain hose. To fix this problem, you will need to remove the air gap and reinstall it according to the manufacturer’s instructions.

8. Pressure Switch Issue

he pressure switch is a safety device that monitors the amount of water in the tub and tells the pump when to turn on and off. If the pressure switch fails, it can cause the pump to run continuously, which will cause the washing machine to fill up with water and overflow.

See also  LG Washer OE Error Code [FIXED] - Causes and Solution

To test whether the pressure switch is failing, disconnect power to the washing machine and remove the hose from the pressure switch. Blow into the hose and see if air is coming out of the other side. If not, then replace the pressure switch.

If your washing machine is still adding water during the spin cycle after you’ve replaced the pressure switch, then there may be a problem with your pump or something else entirely.

9. Clogged or Kinked Drain Hose

If your washing machine is adding water during the spin cycle, it’s likely due to a clogged or kinked drain hose.

The drain hose is the flexible pipe that carries water and laundry detergent from your washer to the home’s drain system. A clog can form in the hose if lint from your clothes collects in it.

A kink can occur if the hose is bent too sharply. Either problem can cause water to back up into your washer during the spin cycle.

You can check for a clog by disconnecting the drain hose from the washer and running water through it. If you see lint or other debris in the hose, clean it out and reconnect it to the washer.

If the hose is kinked, straighten it out so that it doesn’t bend too sharply.

Conclusion

If your washer is adding water during the spin cycle, there are a few possible causes. The most common cause is a faulty inlet valve. The inlet valve allows water to enter the washer, and if it is damaged, it may allow water to enter the washer even when the machine is not in use.

Other possible causes include a faulty pressure switch or a clogged drain hose. If you are unsure of the cause, it is best to call a qualified technician for assistance.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top