Whirlpool Washer Drain Pump Runs Continuously [FIXED]

Whirlpool washer drain pump runs continuously: This is a problem that can be caused by a few different things. First, check to make sure that the washer is draining properly. If the washer is not draining properly, the pump will continue to run in an effort to try and clear the water. Second, check to see if there is anything blocking the pump from running properly.

A leaking washing machine might be the result of a number of issues, from water inlet valves that aren’t functioning correctly to hoses and pumps being clogged or broken. You may find that some interference with your fix is related to the drain hose being positioned too deep into the standpipe, or an issue with the control board.

In this article, I will go into detail about how to troubleshoot a washer that is not draining properly. Hopefully, this will help you to determine what the problem is with your washer and you can easily fix it.

Make sure the drain drum is empty or that the drain filter isn’t clogged before troubleshooting to prevent your drain pump from running. If there is water present, it means the drain pump is not able to drain either partially or completely.

Whirlpool Washer Drain Pump Runs Continuously – Troubleshoot And Diagnosis

Whirlpool Washer Drain Pump Runs Continuously

if you encounter any issues with your washer, use the following troubleshooting tips to fix it. If you need further assistance, contact a certified technician in your area for help.

1. Do a Reset

If your Whirlpool washer drain pump runs continuously, it may be time to reset the washer. To do this, unplug the washer from the power outlet and then plug it back in.

Once the washer is plugged back in, press and hold thePower button for 30 seconds. This will reset the washer and hopefully stop the drain pump from running continuously.

2. Faulty Drain Pump

A washing machine needs to go through several stages to get your laundry cleaner. The first stage is the wash cycle, where water fills the drum and agitates dirt into the spinning water. That water then drains out of the washer as it begins another cycle, known as the rinse cycle.

When the wash cycle has finished, drain pumps help remove almost every drop of water from the washer and push it through to a hose attached to a drain. This negates the need for drying clothes, which can save quite a bit of time and energy.

In doing so, you’ll find that your freshly-washed clothes will carry minimal moisture. This will allow you to dry them in half the time, without risking shrinkage or uneven drying.

Finally, the water drains out completely, and the clothes are nearly dry. If you run into issues with your washer draining or filling, you may need to troubleshoot the problem yourself. More unfortunate problems will require a professional repairman.

Like any other component in the washing machine, the drain pump could have functionality issues that prevent it from working correctly.

When all is said and done, there are two ways a problem with a drain pump might manifest: it can fail to turn on at all, or it can malfunction and be stuck on.

See also  Maytag Washer Stopped Working Full Of Water (How To Fix)

The latter situation can cause your washing machine to automatically run a wash cycle with no more water for the pump to drain, leading to overuse of electricity, inefficient use of detergent, and damage to your clothing and washer itself.

The pump may be a temporary fix, however, certain conditions can cause more damage. Replacement of the pump could end up being the most cost-effective and affordable option, as it prevents the costly replacement or repair of the whole parts set. And using spare parts from a genuine manufacturer would keep your products performing at their best for longer.

But since the drain pump is electric, it’s likely that there’s a problem with its motor or circuit board. This can be dangerous to try and fix yourself; instead of paying someone else to fix your problem you should just buy a new washing machine.

2. Damaged Control Board

If your Whirlpool washing machine doesn’t seem to be draining properly, the first thing you should check is the control board. The control board is responsible for controlling the washing machine’s motor and pump.

If the control board is damaged, it can cause the washing machine’s drain pump to run continuously. This can be a problem because it can cause the washing machine to overheat and break down.

A washing machine‘s control board manages the machine‘s cycles and functions, as well as receiving and interpreting signals from the various sensors located throughout the washer. The control board uses this information to activate the various motors and pumps that make up the washing machine‘s drive system.

The control board is the central nervous system of the washer, and as such, it is a very important component. If the control board fails, the washing machine will not operate.

The control board activates the drain pump to empty the machine’s basin before it starts washing your clothes. Once the wash cycle is complete, it can spin the laundry to remove much of excess water.

It is not unusual for the control board of a washing machine to fail. There are several reasons why this may happen. The most common reason is that the control board is simply worn out from use. Other reasons include electrical problems, such as a power surge, or mechanical problems, such as a loose wire.

In most cases, a failed control board can be replaced. However, if the problem is electrical in nature, it may be necessary to hire an electrician to fix the issue. If the problem is mechanical, it may be possible to repair the washing machine yourself. However, it is always best to consult with a qualified appliance repair technician before attempting any repairs.

3. Water Level Switch Problem

A water level switch is a device used in a whirlpool washing machine to control the amount of water that enters the tub. The switch is located near the bottom of the tub and is connected to a hose that brings water into the tub.

See also  LG Washer dE Error Code [FIXED] - Let's Fix It

The switch has two settings: low and high. When the switch is set to low, less water enters the tub. This setting is used for smaller loads of laundry. When the switch is set to high, more water enters the tub. This setting is used for larger loads of laundry.

The water level switch helps to ensure that clothes are washed properly and that there is enough water in the tub to cover all of the clothes.

If the water level switch fails, it can cause the washer to overflow, which can lead to serious damage. There are several reasons why a water level switch may fail, including:

  • A build-up of dirt or debris on the switch contacts
  • The switch contacts become corroded
  • A problem with the electronic control board

If you notice your washing machine is leaking or overflowing, it’s important to check the water level switch. This simple fix could save you from costly repairs.

To access the switch, you’ll need to remove the washing machine’s back panel.

Once you’ve removed the panel, locate the water level switch and disconnect the wires. Use a multimeter to test the switch for continuity. If there is no continuity, then the switch needs to be replaced.

Replacing the water level switch is a relatively easy task that anyone can do with just a few tools. With a little time and effort, you can have your washing machine up and running like new again.

4. Block Drain Hose

If your washer’s drain hose is blocked, it can cause water to back up into your washer, making it difficult to wash your clothes. There are a few things you can do to unblock your drain hose and get your washer working properly again.

First, check the hose for any kinks or bends. If the hose is kinked, it may be preventing water from flowing through. Straighten out the hose and see if that fixes the problem.

If the hose is not kinked, then there may be a clog further down the line. Try running some hot water through the hose to see if that clears the clog. If not, you may need to use a plunger or a plumbers’ snake to clear the blockage.

5. Drain Hose Is Placed Incorrectly Inside The Standpipe

If your washing machine’s drain hose is not inserted properly into the standpipe, it could cause serious damage to your home. The drain hose is responsible for draining all the water from your washing machine, so if it’s not properly positioned, the water could back up and flood your home.

To avoid this disaster, be sure to check that your washing machine’s drain hose is properly positioned before each use. The hose should be inserted into the standpipe so that the end is at least four inches above the floor.

The drain hose should be placed so that the end is lower than the water level in the washer. This will allow gravity to do its job and keep the water flowing through the hose and into the standpipe. If the hose is not positioned correctly, the water could back up into your washer and cause flooding.

See also  Samsung Washer NF Error Code [FIXED] - KCSCFM Repair

If you’re not sure how to correctly position the hose, consult your washing machine’s manual or call a professional for help.

6. Broken Water Inlet Valve

A washing machine’s inlet valve is responsible for controlling the amount of water that enters the washer tub. The inlet valve is located behind the washer’s control panel and has two water supply lines that connect to it. One line supplies hot water to the valve, and the other line supplies cold water.

The inlet valve opens and closes according to the settings that are selected on the washer’s control panel. When the wash cycle is selected, the inlet valve will open and allow a predetermined amount of hot and cold water to enter the tub. The amount of water that enters the tub depends on the load size that is selected.

Once the correct amount of water has entered the tub, the inlet valve will close and prevent anymore water from entering.

If your Whirlpool washing machine isn’t working properly, it may be due to a broken inlet valve. This is a common problem with these machines, and it can be easily fixed.

If you notice that your washing machine isn’t filling up with water, or if it’s not draining properly, the inlet valve may be the culprit. To check the valve, first make sure that the power is turned off. Then, remove the hose from the back of the machine and check for any blockages. If there are none, then the valve may be broken and will need to be replaced.

Replacing the inlet valve is a fairly simple task that most people can do themselves. However, if you’re not comfortable doing it yourself, you can always call a professional for help.

7. Ensure that Washer Is Level

If your Whirlpool washer is not level, it can cause a number of problems. The washer may vibrate excessively, causing noise and damage to the washing machine. Additionally, an unlevel washer can lead to poor washing results and increased water usage.

To level a Whirlpool washer, start by placing a level on top of the washer. Then, adjust the legs until the bubble is in the center of the vial. Be sure to check all four legs for proper leveling. Finally, tighten the lock nuts on each leg to secure the adjustment.

Final Thoughts

In conclusion, if your Whirlpool washer drain pump runs continuously, there are a few things you can check. First, make sure the washer is level. Second, clean the drain pump filter. And lastly, check the house’s plumbing for a clog. If you have tried all of these things and the issue persists, you may need to call a repairman.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top