Frigidaire Dryer E64 Error Code [SOLVED]

Frigidaire Dryer E64 Error Code is one of the most common error codes associated with a Frigidaire dryer and is known to be one of the most common errors in regard to maintenance and repairs within this piece of equipment.

This error is caused by many different hardware issues with the dryer and can arise for various reasons, including overheating, sensor issues, and even mechanical failure.

If you are like most people, then you know how frustrating it is when your dryer isn’t working. Whether the dryer just isn’t heating up or you keep getting error codes, it is really annoying to have to go through this every time you do laundry.

Additionally, if your dryer stops working altogether, then you will have to make a trip to the repair shop and that can be quite expensive.

Frigidaire dryer E64 error code means that your dryer has burnt or faulty heating element. Sometimes this error can also be caused due to blown thermal fuse, defective cycling thermostat or faulty control board.

This Frigidaire dryer E64 error code can be easily solved with the help of a qualified appliance repair professional. If you are not skilled enough to fix this problem, then it is advised to call the authorized servicing agent for help.

Frigidaire Dryer E64 Error Code – Troubleshoot And Diagnosis

There are several reasons why your Frigidaire dryer might produce an E64 error code. When you run into an issue with your Frigidaire dryer, it may be difficult to troubleshoot the problem. Let’s have a look at the possible causes and solution.

1. Burnt Heating Element

In most instances, the error code E64 on a Frigidaire dryer means the heater assembly is broken — specifically a heating element that has either burnt up or been shorted to the rest of the unit.

A heating element in a dryer is responsible for providing the heat that is used to dry clothes.

The element is usually located near the bottom of the dryer, and it works by using electrical resistance to generate heat. The heat generated by the element is then used to warm the air inside the dryer, which in turn helps to evaporate any moisture that is present on the clothes.

A dryer’s heating element can fail for a number of reasons. The most common reason is a build-up of lint in the element’s housing. When lint accumulates, it insulates the element, which prevents it from getting hot enough to dry clothes. The element can also fail if it overheats due to a malfunction in the dryer’s thermostat or thermal cut-off switch. In some cases, the element simply wears out over time and needs to be replaced.

If your dryer isn’t heating, the first thing to do is test the heating element to see if it’s broken. To do this, disconnect the dryer from the power source and remove the back panel. Locate the heating element and use a multimeter to test it for continuity. If the element doesn’t have continuity, it needs to be replaced.

Here are the steps:

1. Unplug the dryer from the wall outlet.
2. Remove the back panel of the dryer to access the heating element.
3. Use a multimeter to test the heating element for continuity. If the element is not working, it will need to be replaced.
4. Remove the old heating element and replace it with the new one.
5. Reattach the back panel of the dryer and plug it back into the wall outlet.

Test your dryer again and see if the error is now cleared or not.

2. Blown Thermal Fuse

A thermal fuse is a safety device that has been mandatory in all dryers since the 1980s. This fuse burns itself out before overheating or fire starts, which makes it an excellent way to extend the life of your clothes dryer.

A dryer’s thermal fuse is a safety device that is mounted on the dryer’s heating element.

If the dryer overheats, the thermal fuse blows and cuts off power to the dryer. The dryer will not start if the thermal fuse is blown. When this happens, you will see the E64 code on the Frigidaire dryer.

The dryer thermal fuse will be used one time, and then it’s done.

When the thermal fuse on a dryer blows, it is primarily for safety reasons; however, this can lead to a number of issues: the machine will not turn on, you may see an error code or the drum could continue to rotate without heat from the heating element.

To find and fix a fuse we suggest following these steps:

Disconnect power when testing the fuse

Find the wires to the fuse

Use a multimeter to test if those wires are conducting. (You can use your phone’s multimeter app or buy a digital multimeter)

To find out whether or not your fuse is bad, hold one probe of your multimeter against each wire, with them touching the middle terminal of the fuse itself.

This should be a “test” terminal that has an indented corner to ensure you’re placing it in the correct spot.

Ready for results? Any other reading means that your fuse is bad and needs to be replaced.

So why is it that dryer fuses blow? There are a number of possible causes, ranging from inadequate wiring to faulty appliance parts to worn-out dryer ducts.

You can fix the broken dryer within minutes by simply changing the fuse, but it’s ideal to understand the reasons behind its failure.

Before using your dryer, check the venting system for any obstructions that cause inadequate airflow, check the blades on the heater and fan for signs of damage, and make sure to check the cycling thermostat — anything can lead to a blown fuse.

3. Defective Cycling Thermostat

If a cycling thermostat fails in your Frigidaire Affinity dryer, it can also cause E64 error code to be thrown.

The cycling thermostat is a key part of dryer operation. It monitors the internal temperature of the machine and turns off the heat when it reaches a certain level — preventing the dryer from overheating.

The cycling thermostat is an electrical device used to monitor the air temperature inside a clothes dryer. It acts as a safety measure, turning the dryer on and off as needed to maintain a constant temperature.

A defective cycling thermostat is often the culprit when you have a dryer with no heat.

Here are some tips on how to change a cycling thermostat on a dryer:

1. Disconnect the power to your machine
2. Pull the dryer away from the wall
3. Remove the screws that hold the rear access panel in place
4. Remove all wires connected to the thermostat and remember where they go.
5. Note: All parts of the old thermostat should be removed from the new one.
6. Remove the wires and remove the old thermostat
7. Reconnect the wires to the new thermostat
8.  Replace the access panel and screws.
9. Reconnect power to the machine and test.

In order to test whether or not your cycling thermostat is still working properly, follow these steps:
1. Remove the wires from one of the connectors
2. Attach a probe to each connector
3. Set your digital multimeter to the “R X 1” or “Continuity” function
4. A thermostat that’s still good should give you a reading of infinity.

Frigidaire Affinity Dryer E64 Code

When it comes time to troubleshoot the Frigidaire Affinity dryer’s control panel, there are three parts warranting further investigation. The first is the heating element, which generally wears down over time and will require replacement.

Next, is the thermal fuse, which can melt due to slight spikes in temperature that may occur if your dryer isn’t properly vented and ventilated.

If you are getting Frigidaire Dryer E68 code, then you can find solution here as well.

Finally, there is a thermostat, which can also be damaged due to improper ventilation.

The heating element can be replaced in about an hour without the need for professional assistance. While the dryer is operating and the heating element reaches a temperature of 230-degrees Fahrenheit, unplug the machine and remove the two screws holding the element in place. Remove the old heating element and make sure the new element lines up properly with the holes in the dryer and then reassemble.

Final Thoughts

When your Frigidaire Affinity dryer begins to display an error code of E64, check the heating system as a potential culprit. This system consists of the heating element, thermal fuse, and the cycling thermostat.

If your machine is displaying either error code, examine each part with a multimeter to quickly identify which part is the problem.

Once you’ve determined which part is causing the problem, be sure to replace it with an exact replacement part to get your dryer back up and running.