GE Washer H20 Supply Error [Quick Solution]

If your GE washing machine is displaying the H20 error code, it means that there is a problem with the water supply. This can be caused by a number of different things, such as a blocked hose or a problem with the water inlet valve. In most cases, the H20 error can be fixed quite easily.

GE is a trusted name in washers, but even the best machines can have glitches. If your GE washer is giving you an error code, it can be frustrating trying to figure out what it means.

Most error codes on GE washing machines are generated by the electronic control board and are easy to interpret.

If your GE washing machine is displaying an error code, don’t hesitate to contact a service technician for assistance. With proper diagnosis and repair, your GE washing machine will be back up and running in no time.

If your GE washer is displaying the “H20” error code, it means that there is an issue with the water supply. The most common causes of this error are: inadequate water filling, blocked or closed water inlet valve, and faulty water inlet hoses.

If you’re experiencing the “H20” error code, check to make sure that the water inlet valve is open and that the water hoses are not blocked or kinked. If these solutions don’t work, you may need to replace the water inlet hoses.

GE Washer H20 Supply Error – Troubleshoot And Diagnosis

If you’re a GE washer user, you know that those error codes can be a real pain to decipher. But never fear! This guide will tell you everything you need to know about what those error codes mean.

GE Washer H20 Supply Error

Depending on the model of GE washer you are using, the error code may indicate a few different things. However, there are some common issues that these codes usually point to.

1. Do A T06 Pressure Switch Test

If your GE washing machine isn’t draining properly, the first step in diagnosis is to check the T06 pressure switch. This switch controls the washing machine’s drain pump, and if it’s not working properly, the washer won’t be able to drain water properly.

See also  How To Unlock Whirlpool Washer [Step By Step Guide]

To test the T06 pressure switch, you’ll need to put your washing machine into test mode. Test mode is a special diagnostic mode that allows you to test individual components of your washing machine. To enter test mode, press and hold the “Start/Pause” and “No Spin” buttons for three seconds. Once you’re in test mode, you can use the “No Spin” button to cycle through different tests. To test the T06 pressure switch, press the “No Spin” button until you hear a click.

If the T06 pressure switch test is positive, it means that the water inlet valve and hoses are not the culprit. The most likely cause of the problem is a circuit board or electrical issue.

2. Check Water Inlet Valve

The function of a water inlet valve in a GE washer is to help regulate the amount of water that enters the washer during each cycle. The valve is located near the bottom of the washer and is connected to the water supply line. When the washer is turned on, water flows from the valve into the tub.

The amount of water that enters the tub depends on the settings that are selected on the washer. The water inlet valve must be working properly for the washer to function correctly.

If your GE washing machine isn’t filling with water, the first thing you should check is the inlet valve. To do this, you’ll need to use a multimeter to test for continuity. If there is no continuity, then the inlet valve needs to be replaced.

To replace the inlet valve, first shut off the water supply to your washing machine. Then, remove the hose from the back of the machine and disconnect the wires from the valve. Once the old valve is removed, install the new one and reattach the hose and wires. Finally, turn on the water supply and test your washing machine to make sure it’s filling properly.

See also  GE Washing Machine Squeaking Noise When Agitating - Let's Fix It

3. Check Filter

The function of the filter in a GE washer is to help remove lint, hair, and other debris from clothing. The filter is located in the bottom of the washer tub and can be accessed by removing the kick panel.

To clean the filter, simply remove it and rinse it with warm water. Be sure to replace the filter after cleaning.

4. Clogged or Kink Hose

If your GE washer isn’t draining properly, there could be a clog or kink in the hose.

To check for a clog, first remove the hose from the washer. Then, insert a drain snake into the hose and try to clear the blockage.

If your GE washing machine’s hose is clogged, it can cause poor draining and even flooding. Luckily, this is an easy problem to fix. First, unplug the washing machine from the power outlet. Next, remove the hose from the back of the machine. Using a plunger, clear any debris that may be blocking the hose. Once the hose is clear, reattach it to the machine and plug it back in.

If that doesn’t work, you may need to replace the hose.

To check for a kink, simply inspect the hose for any bends or kinks. If you find one, straighten it out and see if that fixes the problem.

5. Defective Control Board

The control board in a GE washer is responsible for operating the washer’s various functions. The board typically has a series of switches or buttons that activate the washer’s different settings, such as the cycle selection, water temperature and spin speed.

The control board also regulates the washer’s motor speed and timer. In some models, the board may also include a diagnostic system that can be used to troubleshoot problems with the washer.

A GE washer H20 supply error is due to a defective control board. The control board controls the water supply to the washing machine. If the control board is defective, it will not allow the water to enter the washing machine. This can cause the washer to fill slowly or not fill at all. The washer may also stop mid-cycle or not start at all.

See also  Washing Machine Makes Loud Noise When Draining [SOLVED]

You can try resetting the washer, but if that doesn’t work, you’ll need to replace the control board.

6. Water Supply Issue

If you have a GE washer and it is displaying the H20 error code, this means that there is no water supply to the washer. This can happen if the water supply to your home is interrupted, or if there is a problem with the public water supply.

If you think that your water supply has been interrupted, you should check with your local water supplier to see if there is a problem. If there is not a problem with the public water supply, then the most likely cause of the H20 error code is an accidental break in the water supply line to your washer.

7. Reset The Washer

If your GE washing machine isn’t working properly, you can try resetting it.

First, unplug the machine and wait for 15 seconds. Then, lift and lower the lid 6 times within a 12 second time limit.

This should reset the machine and get it working again. If this doesn’t work, you may need to call a repairman.

Final Thoughts

In conclusion,the GE washer H20 supply error can be a frustrating problem to have.

However, by following the tips in this article, you should be able to fix the issue quickly and easily. If you are still having trouble, you may want to contact a professional for help.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top