Whirlpool Washer Fills Then Drains Immediately [SOLVED]

If your Whirlpool washing machine fills then drains immediately, there are a few things you can check to try and fix the problem.

First, make sure there is no siphoning issue causing the water to be pulled back out of the machine. Next, check the height of your house drain. If it’s too low, the water may not be able to drain properly. Finally, check the control setting to make sure it’s not set to ‘rinse’ or ‘drain.’ If none of these solutions fix the problem, there may be an issue with the pressure-activated switch.

Whirlpool Washer Fills Then Drains Immediately – Troubleshoot And Diagnosis

The worst thing in the world is having a washer that doesn’t use water. Water enables washing clothes, but without water all that’s possible is just mopping the floor.

Whirlpool Washer Fills Then Drains Immediately

Let’s see some of the fixes.

1. House Drain Height Issue

If your washer is filling and draining immediately, it is likely due to the house drain being too low. The washer needs a siphoning action to work properly, and if the drain is too high, the water can just drain back out.

The house drain needs to be at least 30 inches high in order for the washer to work properly. If the drain is pushed inside, it should be no more than 7 inches. There should also be an air gap between the house drain and the washer.

The best way to fix this problem is to make sure that your washer is at least 30 inches high and that the air gap is properly installed.

See also  Why Is My Washing Machine Leaking From Bottom? [SOLVED] - Let's Fix It

2. Incorrect Settings

The most likely culprit is incorrect settings. Check to be sure the washing machine is properly plugged into an outlet and that the water supply valves are fully open.

Also, check the washing machine’s settings to be sure they are correct for the load size and type of fabric you’re washing.

To fix this, first check that the water level is set correctly. If it is, then the problem may be with the wash cycle time. Try increasing the cycle time by a few minutes.

First, open the washer’s lid and find the control panel. Locate the water level knob or button and turn it to the desired amount of water. For most loads, you’ll want to choose the medium or high setting.

If your washer has a dial instead of a knob, rotate it until the indicator arrow points to the correct water level. Once you’ve set the water level, close the lid and press the start button. The washer should begin filling with water.

3. Inlet Valve Problem

The inlet valve controls the flow of water into the washer and is located behind the control panel.

The inlet valve controls the flow of water into the washer. If it’s not functioning properly, water will fill the tub and then drain out immediately.

To check if the inlet valve is the issue, first make sure that there is no debris or sediment blocking it. If that’s not the problem, then the valve may be faulty and will need to be replaced.

See also  LG Washer LE Error Code [FIXED] - Causes and Solution

To test the inlet valve, unplug the washer and remove the access panel to expose the valve. Test for continuity between the two terminals on the valve using a multimeter. If there is no continuity, replace the inlet valve.

4. Clogged or Kinked Drain Hose

A clogged drain hose is the most common cause of this problem. The hose can become clogged with lint, hair, or other debris. If this happens, the water will not be able to flow through the hose and into the drain.

A kinked drain hose can also prevent water from flowing into the drain. If your hose is kinked, it may need to be replaced.

If you have a clogged or kinked drain hose, you should clean it out as soon as possible. This will help to prevent your washing machine from overflowing and causing water damage to your home.

5. Pressure Switch Problem

If your Whirlpool washer is filling and then draining immediately, the pressure switch may be the issue. The pressure switch is responsible for telling the washer when to stop filling with water. If it’s not working properly, the washer will continue to fill and then drain.

To test the pressure switch, open up the washer and locate it. The pressure switch is a small, round device with two wires coming out of it. Once you’ve located it, use a multimeter to test it for continuity. If there is no continuity, the switch needs to be replaced.

If the pressure switch is working properly but your washer is still filling and draining immediately, there could be an issue with the timer or control board. Both of these components tell the washer when to fill and drain.

See also  6 Reasons Why Washing Machine Keeps Tripping Breaker - Let's Fix It

Final Thoughts

In conclusion,if your Whirlpool washer is filling and draining immediately, there are a few things you can check. First, make sure the water supply valves are turned on. Next, check the inlet hoses to ensure they’re not kinked or clogged.

Finally, clean the washer’s filters. If you’ve tried all of these things and your washer is still not working properly, you may need to call a repairman.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top