There are many reasons why you might want to reset KitchenAid dishwasher. Maybe the dishes don’t get clean, or maybe you just want to change the settings. Resetting a dishwasher is quick and easy! Follow these steps below for information on how to do it.
KitchenAid dishwashers are some of the best on the market. They are known for their reliability and durability. Resetting your KitchenAid Dishwasher is a simple, 2-minute task that can save you money in repair costs.
How to Reset KitchenAid Dishwasher
Like a computer, resetting the KitchenAid dishwasher’s control panel can fix the problems you are experiencing.
To reboot the KitchenAid dishwasher, disconnect it from the power source and, after 1-minute, plug it back in.
NOTE: Your dishwasher doesn’t have any power? Don’t worry, just check if the Control Lock has been activated. If it is active, your control panel will not function at all and a red “Padlock” may be illuminated. Be sure to consult the Owner’s Manual for your model of the appliance to learn how you can de-activate this lock before attempting anything else.
Sometimes you may have a small electrical hiccup with the dishwasher that can be fixed by rebooting. It will also help reset all the previous settings, which may be stopping the normal function of the dishwasher.
Follow the below steps to do a simple reboot for KitchenAid Dishwasher.
- Turn off the circuit breaker.
- Turn the power off to the dishwasher and unplug the power cord.
- Wait for at least 5 minutes.
- Plug the dishwasher back to the power source.
- Turn the circuit breaker to the on position and turn your dishwasher on.
This will reboot the KitchenAid dishwasher and from now you can use the dishwasher normally.
KitchenAid Dishwasher Cycle Reset
If you just need to reset the dishwasher cycle, then please follow the below steps:
- Press and hold the Cancel or Cancel Drain Button for 3-5 seconds.
- It will cancel and reset KitchenAid dishwasher.
Now you can run the new cycle with new settings.
KitchenAid Dishwasher Control Panel Reset
When powering down the dishwasher and turning it back on is not working, It may be best to reset the control panel. Resetting a dishwasher is easy.
You can reset it by pressing two buttons on the front of the dishwasher at least five times each for a grand total of ten presses. The dishwasher door must be fully closed while the buttons are both pressed.
Some dishwashers reset by pressing the buttons four times, but it is recommended to press each button five times for most models.
The Sequence of pushing buttons is:
- Hi-Temp Scrub or Hi-Temp Wash button
- Heated Dry
- Energy Saver Dry or Air Dry button
These reset sequences will vary based on different models. So, please check your owner’s manual for the correct sequence.
Press of the buttons may activate, blink or light up one of the LED panels above each button. The dishwasher will likely go through a series of self-diagnostics, such as the pump draining or other functions.
Do not give the dishwasher any input during the self-assessment period. It may take 2-3 minutes to complete when the dishwasher completes its diagnostics process. Press Cancel or Cancel-Drain to start a drain cycle.
These cycles typically last two minutes. Once the drain cycle is complete, it will be possible to start a new desired cycle.
If you want to know how to Reset KitchenAid dishwasher, follow our instructions. Resetting the machine will help it operate smoothly and ensure there are no errors in its programming.
Resetting your appliance is a lot like resetting an iPhone or Android phone: It sets things back to factory settings so that everything starts fresh. You may need to do this if the dishwasher has been unplugged for an extended period of time, leakage, drainage issue, or during the installation process.
Resetting the KitchenAid dishwasher will also be helpful if there were any problems with water pressure after installing a new sink faucet set-up! So make sure you have all these moments covered by following our guide and using as many tips as possible.
Hi there! I’m Sam Hendricks, and I’m a repair technician and expert. I created this website to help people like you save money and time by fixing your own appliances.
Over the years, I’ve seen people spend a lot of money on unnecessary repairs or replacements. That’s why I decided to share my expertise and create easy-to-follow guides for fixing appliances on your own.