Samsung dryers are well-known for their high quality and dependability. Samsung is one of the top providers of washers, dishwashers, refrigerators, and other household appliances. However, Samsung dryers are also prone to a particular error code that can be very frustrating.
Samsung Dryer hE Error Code indicates that the dryer is getting too hot. This article will provide you with some troubleshooting tips so you can identify an issue or fix it yourself and get back to business.
What Does The Samsung Dryer hE Error Code Mean?
Samsung Dryer hE Error Code occurs when the dryer overheats. This can be caused by debris clogging the vent system or a defective lint basket preventing proper airflow. Fix it by cleaning these parts or replacing them if they’re damaged.
Often, there’s nothing more to do than to restart a malfunctioning appliance. This is especially true for dryers and washing machines, for example, which can develop errors over time that can only be fixed by unplugging and restarting the machine.
The first thing you should try is resetting the error code. The instructions are as follows:
- Unplug your dryer from the wall. If you have a power cord, disconnect it from the outlet.
- Wait for 30-60 seconds.
- Plug your machine back in and restart it. If you’re using a power cord, plug it into an outlet.
- Try running your program again.
How To Fix Samsung Dryer hE Error Code
If you have a gas dryer, open the shutoff valve at the dryer’s connection to the gas line. Then, unplug and disconnect the dryer. Inspect each part of the dryer — coils, wires, etc. If there are any visible damages or corrosion, repair them yourself or contact a service provider.
In the case of an electric dryer, make sure that the dryer’s power switch is off, turn it on, and use it again. Choose a cycle and make sure the equipment doesn’t shut off. If the power switch is on, but the machine still turns off, there may be a problem with the heating element. Unplug the dryer and check the wires to ensure they are secure.
If you see an “HE” error code on your Samsung dryer, don’t worry. You can take a few troubleshooting steps to get the issue resolved using the information provided in this guide.
If the dryer is getting too hot, it may be due to a clogged lint filter. Follow these steps to keep your dryer working like new:
- Remove and clean the lint filter.
- Vacuum out any lint or debris stuck inside the slot-shaped area in the back of the dryer.
You should also check your dryer vent to ensure that there’s proper airflow. Let the dryer run for 5 minutes, and then go outside to check if the air is flowing out of the exhaust vent. Suppose you feel the air, great! If you don’t, it could be time to call in a pro.
Good dryer maintenance is the key to a long-lasting, safe, and reliable machine. By keeping your lint trap clean on a regular basis, you can prevent fires from flammable clothes and reduce the amount of time you spend waiting around for your clothes to dry.
Faulty Cyclic Thermostat
The Samsung dryer hE error code may also be the result of a cycling thermostat. Dryers use a unique feature called a cyclic thermostat, which is a control device that automatically turns off the heat when it reaches a certain temperature. This safety component is found in virtually all dryers, and it’s there to protect your home and your clothing from overheating.
However, sometimes this metallic device fails. This defect can allow the dryer to overheat. This component is found at the rear of the dryer; look for a small metallic device with a wire attached to it.
If you suspect a thermostat is broken, you can test it to confirm. First, disconnect the wires from the old thermostat and attach them to your multi-meter. Then, place each probe on a terminal and read the results. If the measurement comes back 0 or near 0, there is likely no issue with the thermostat.
If it reads infinite, that indicates a failure in the wiring or in the cyclic thermostat itself. Thermostats are relatively inexpensive and easy to replace.
Broken Heating Element
The heating element is designed to warm the inside of the dryer drum before the air reaches it so that every piece of clothing receives adequate heat. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. This means that the dryer is receiving excessive heat and hence overheats.
If you’re troubleshooting, use a multimeter to test each terminal for continuity. If it has continuity to the case, the heating element is shorted out. If not, then you have a different problem. Replace the heating element if needed.
Worn Out Felt Seal
To optimize energy efficiency, dryers should be properly sealed: with a thin, felt seal on the front of the drum and a thicker fabric seal around the back. When these two seals are in good condition and properly placed, they hold heat inside of the drum — keeping the dryer within its set temperature range.
If the felt seal is ripped, worn, or missing, air will be able to enter the back of the drum — letting heat escape and causing your dryer to overheat.
The felt seal should form a tight seal around the drum — if it doesn’t, replace it. Before you do, however, make sure that all of the other parts of your dryer are in good working order! If everything else is fine, install a new seal.
Samsung Dryer Overheating HE Code
A dryer with the HE code may overheat due to a problem with the heating element. The element may be faulty or the dryer may be overloading the element. The element may need to be replaced or the dryer may need to be repaired.
It is common for the dryer to overheat when the vent hose is full of lint. The vent hose needs to be cleaned to ensure proper air flow and dryer operation. This problem can also occur if the vent hose is kinked or has too many bends.
Check the air circulation around and through the dryer as well as the air vent.
There are a number of ways you can troubleshoot the Samsung Dryer hE error code to identify and fix the problem. If you’ve exhausted all other options, then it might be time for professional help.
If you’re dealing with this issue and need help, let me know in the comments below! I’ll do my best to get back to you as soon as possible.
Hi there! I’m Sam Hendricks, and I’m a repair technician and expert. I created this website to help people like you save money and time by fixing your own appliances.
Over the years, I’ve seen people spend a lot of money on unnecessary repairs or replacements. That’s why I decided to share my expertise and create easy-to-follow guides for fixing appliances on your own.