Shark is one of the most popular brands of vacuum around. However, it is not uncommon for these vacuums to break down. Some of the more common reasons for your Shark not charging include: a faulty charger, a broken outlet, or an electrical problem with the vacuum itself. If you are feeling frustrated because you cannot use your Shark, then you can follow these steps to try and fix the problem.
There’s nothing more frustrating than having your vacuum not charge. A chore that might have taken 30 minutes can quickly balloon into a time-consuming, endlessly frustrating task. But why? Why Shark Vacuum Not Charging?
If your Shark vacuum is having trouble charging, check the following: Make sure the charging base is plugged in to an outlet. If it’s plugged into a power strip or surge protector, try plugging the unit directly into a wall outlet to charge the vacuum.
When your Shark vacuum stops charging, don’t panic — we’re here to help! Before you head over to the Shark service centre or buy a new vacuum, try these easy steps!
Shark Vacuum Not Charging – Troubleshoot And Diagnosis
An uncharged vacuum is a frustrating thing. It means that you can’t complete an important cleaning task. It also means that you’ll have to waste time looking for the culprit behind your vacuum’s sudden inability to charge. So, what are the possible causes of such a problem?
There are a few reasons why this may have happened. The most common is that the outlet has gone bad. Another could be that the battery has lost its ability to hold a charge and needs to be replaced. Or, it may just have gathered too much dust on the contacts and needs to be cleaned.
1. Check The Outlet
If there’s something wrong with your vacuum, it can be hard to figure out what the problem is. Luckily, you can troubleshoot your vacuum yourself and fix it. The first step is to check the power source.
Your vacuum won’t work if it’s not charging. If you keep the charger plugged into the same power outlet and it still doesn’t work, try a different outlet or a different charger.
Sometimes you may not be able to tell whether a vacuum cord is working, but you can always test it by plugging in your phone or lamp into the same outlet. If the phone will charge or the lamp turns on, then you know the outlet is working. If it fails then Outler is Faulty.
Plug the Shark vacuum charger into a different outlet. If it still doesn’t charge, try charging it in another room. If it charges in another outlet or another room, then your first outlet is faulty. If your vacuum still won’t charge, then check to see if you have the charging cable connected to the machine correctly.
2. Check The Shark Vacuum
The Shark vacuum has a power issue. Make sure that the battery is fully charged and that it’s plugged in. Replace your cord if need be, and ensure that the wall plug is functioning properly. Check for any cracks around the charger port of the vacuum, especially at the seam where the charging port meets the body of the vacuum.
You might have an issue with your Shark vacuum. Try plugging it directly into the wall and turning it on. If the suction is strong and the vacuum is functioning normally as you vacuum, then your Shark is simply experiencing a low battery. Charge the vacuum for 12 hours before using it again.
If your Shark vacuum runs well when it’s unplugged, but loses suction power or stops running when it’s plugged into the wall, then the most likely culprit is the charger or battery. It’s best to first test your vacuum with the charger that shipped with your machine. If the problem still persists, the next step would be to replace the battery or charger altogether.
3. Use New Batteries
Just like every battery, Shark vacuums age over time. With each charge, the battery becomes less and less powerful. Eventually, your Shark will lose the ability to hold a full charge, leaving you with a vacuum that doesn’t have the power it once did.
This is often a problem for vacuums that are several years old, but it could also be caused accidental damage such as damage from water. Check the battery compartment for any signs of leakage and replace the battery if necessary.
When you’re in the middle of cleaning, a dead Shark vacuum battery can be a nightmare. Replacing the battery is easy — as Shark vacuums come with explicit instructions on how to do it.
Most Shark vacuums take 16 hours to charge. If your vacuum doesn’t last for a long time after it’s fully charged (3-8 minutes) then you have to replace the battery.
If you’ve ever had a Shark vacuum, you know how great they are. They clean hardwood floors and tile even more efficiently than other vacuums. But over time, the battery life starts to fade to the point where your vacuum barely makes it through one room before needing to be plugged in. It’s time to replace the battery.
4. Clean the Charger and Battery
Sometimes the battery won’t charge because the contacts aren’t touching each other properly. To fix this error, clean the charger and the battery. Use a dry cloth to wipe down the outside of the charger and both contacts on the battery. Then use a toothpick or paperclip to remove dust or debris from inside the charger port so that it can make contact with the battery.
If Shark is not charging, you need to unplug the charger and plug it back in for it to register. You can also take out the battery, blow dry the holes, and put it back in.
If you have tried all of the above and your Shark vacuum is still not working, use a dry microfiber cloth to clean the filter and any other areas where hair might’ve built up.
Avoid using a damp cloth; dry microfiber cloths are best for cleaning up your dust sucker. If water droplets are left behind, they can contribute to bad connection — which is why we’d recommend only using a dry microfiber cloth.
Wiping down the contact points and the surrounding areas on your vacuum is a crucial step in keeping your device running smoothly. Not only that, it helps to avoid any potential fire hazards or electrical shocks. If you don’t mind, I’d like to offer a suggestion for future reference. When cleaning, use a lint roller instead of your hands to ensure that no particles are left behind between the charging points.
Once you’ve cleaned the dirt buildup, plug in your vacuum and place it on the charging base. If the device powers up and the LED goes from red to green, then you should be good to go!
5. Clean the Shark Vacuum
The Shark vacuum is a great product, but sometimes it can have some issues. Most of the time, there isn’t anything wrong with the canister or hoses — which are the first places people tend to check when troubleshooting the vacuum. You should clean it out and test it again before assuming the problem is a part issue. If all else fails, you might need to buy a new vacuum.
To clean the Shark Vacuum follow below steps,
Dump the debris. Rinse the canister with water, and allow it to air dry completely before returning it to the vacuum. If a full container is left in the vacuum, dirt and fine dust particles will be ejected from the unit rather than sucked up into the canister.
Remove the attachments and detach the dust cup by lifting the release lever. You can remove any clumps of debris that may have lodged themselves in the crevices. Use a broom handle or even your finger to poke out debris — always be cautious when poking around inside a vacuum.
Just be sure to pull out all of the hair and other debris that can be stuck in between the head of the vacuum and try not to leave anything inside while you are trying to clean it.
The shark vacuum cleaner is equipped with a rolling brush on the head of the machine. The brush can get hair tangled around it, which can be a problem because the hair will collect with other debris and create clogs. If necessary, you can cut through trapped hair with scissors, but you should also remember that you can remove the brush from the vacuum head to clean it.
To keep your shark vacuum working well, try not to let the filter get too dirty. Check it regularly and clean it every time you vacuum. When charging the unit, make sure that the power button is off.
If this action does not work and you can’t figure out what to try next, contact customer service for advice on getting your vacuum back up and running again.
6. Replace It
If your Shark vacuum is having issues that you can’t solve, you have a few options. You can hire a local vacuum repair shop to diagnose the problem and fix it for you. They’ll also have replacement parts for your vacuum that you can buy.
You can get replacement parts for your Shark directly on the company’s website — just enter your model number and you’ll get access to everything you need, whether that’s Shark accessories or parts.
Shark also has a Support Center you can use to troubleshoot problems you might be having with your vacuum or find out how to best clean up a mess.
Shark Vacmop Not Charging
For those who own a Shark vacuum, you may have run into the problem of your vacuum not charging. This simple fix will help you save time and money.
Shark Vacuum is not charging. There could be a few reasons for this. But let’s go through them one at a time. You may have a broken charger, or even a broken power cord, but that doesn’t explain why the plug in your wall is working fine. Another reason might be because there is hair wrapped around the brushes. If that’s the case, Don’t worry- it can easily be fixed!
When your Shark Vacmop doesn’t charge, the problem could be a dirty outlet, old batteries, or a clogged vacuum — all easily solvable. First, try cleaning the charging station and plugging it into another outlet. If that doesn’t work, put in new batteries; they may just be worn out. These batteries are rechargeable and last up to three years.
Shark Cordless Vacuum Won’t Charge
The Shark vacuum cleaner, while powerful and solid, has a problem that is inherent in the design of its battery systems. When the battery degrades, it becomes impossible to charge. While replacement batteries are available through Amazon or third-party resellers, this is an expense that vacuum owners did not anticipate and often cannot afford.
When your Shark cordless vacuum doesn’t charge, there are a few things you can try to fix the issue. First, make sure any debris is removed from around the charging station and that the plug is firmly in the outlet. Next, test each of the battery contacts to make sure they aren’t bent or dirty — if they are clean and straight, replace the batteries as they may be over-used.
Shark Handheld Vacuum Not Charging
Handheld Vacuum are popular among homeowners who want a vacuum they can carry around the house with them. These devices come with strong suction and powerful motors that let you clean crevices, upholstery, and even dust your ceiling fan. Given that they don’t need to be plugged in to work, these appliances can be taken anywhere.
Does your Shark handheld vacuum seem to be runnin’ a little slow? We have several troubleshooting tips to help you out. If the problem is a dirty charging station, use a slightly damp (not wet) microfiber cloth to wipe it down. Check the battery contacts on the bottom of the vacuum, and on both ends of the charging base, to make sure they’re clean.
If your Shark vacuum is not charging, there are a few things you can do to try to fix the problem. First, ensure that the slot for the batteries is cleaned of any dust or debris.
Next, make sure that your outlet has power by plugging in another device. If that fails, check the charging port on your vacuum for any damage or dirt. If all else fails, you may need to replace your batteries or charging station.
If you’re having problems with your vacuum and can’t figure out what to do, get in touch with a vacuum repair service. If it’s within the warranty period, you might be covered.